Getting a flat tyre is never ideal, but knowing how to fit a spare wheel can save you a long wait and get you safely back on the road. At Kinson MOT Centre, we often meet drivers in Bournemouth who’ve never changed a wheel before – so this guide is written in plain English, from technicians who do this every day.

If at any point you don’t feel safe or confident, stop and call for help. And if you manage to fit the spare, remember: it’s temporary. Get the tyre repaired or replaced properly as soon as possible.

Before You Start: Safety First

Before touching anything, make sure you’re safe.

What to do immediately:

  • Pull over to a safe, flat location (lay-by, car park, quiet road)
  • Turn off the engine
  • Apply the handbrake
  • Put the car in gear (or Park if automatic)
  • Turn on hazard lights
  • Ask passengers to exit the car and stand safely away from traffic

If you’re on a motorway or smart motorway and can’t change the wheel safely, do not attempt it. Call breakdown recovery.

What You’ll Need

Most cars come with the following in the boot (usually under the floor panel):

  • Spare wheel (full-size or space saver)
  • Jack
  • Wheel brace (lug wrench)
  • Locking wheel nut key (very important – often forgotten)
  • Owner’s handbook (helpful for jack points)

Check you have these before starting.

Step 1: Loosen the Wheel Nuts (Before Jacking)

This is a common mistake – always loosen the nuts before lifting the car.

How:

  • Remove the wheel trim (if fitted)
  • Fit the wheel brace to each nut
  • Turn anti-clockwise
  • Loosen each nut about half a turn
  • Do NOT remove them yet

If the nuts are very tight, use your foot carefully on the brace for extra leverage.

Step 2: Position the Jack Correctly

Every car has specific jacking points along the sill.

What to do:

  • Locate the jacking point nearest the flat tyre (usually marked or shown in the handbook)
  • Place the jack on solid ground
  • Make sure it’s straight and stable before lifting

Never jack the car anywhere else – incorrect placement can damage the car or cause it to fall.

Step 3: Jack the Car Up

  • Slowly raise the car until the flat tyre is just off the ground
  • Don’t lift it higher than needed
  • Keep hands and feet clear while lifting

Never put any part of your body under the car while it’s on the jack.

Step 4: Remove the Wheel Nuts and Flat Tyre

Now:

  • Fully remove the loosened wheel nuts
  • Place them somewhere safe (they roll easily)
  • Carefully pull the flat wheel straight off

Lay the flat wheel on its side nearby – don’t leave it standing upright where it can roll.

Step 5: Fit the Spare Wheel

  • Line the spare wheel up with the wheel bolts
  • Push it firmly onto the hub
  • Hand-tighten the wheel nuts one by one
  • Make sure the wheel sits flush against the hub

Do not fully tighten the nuts yet.

Step 6: Lower the Car and Tighten the Nuts

  • Slowly lower the car until the tyre touches the ground
  • Remove the jack
  • Use the wheel brace to fully tighten the nuts

Tighten in a star pattern (opposite nuts), not in a circle. This ensures the wheel seats evenly.

Step 7: Final Checks

  • Double-check all nuts are tight
  • Refit the wheel trim if possible (often won’t fit space savers)
  • Put the flat tyre and tools back in the boot
  • Wash your hands if needed

Important: If You’re Using a Space Saver Wheel

Many modern cars come with a space saver spare.

You must know this:

  • Maximum speed is usually 50 mph
  • Short-distance use only
  • Handling and braking will feel different
  • Do NOT use for long journeys or motorway driving if avoidable

A space saver is to get you home or to a garage, not to continue driving normally.

After You’ve Fitted the Spare

As soon as possible, you should:

  • Get the damaged tyre repaired or replaced
  • Have wheel nuts checked and torqued properly
  • Refit a full-size wheel if you used a space saver

Driving long-term on a spare can be unsafe and may invalidate insurance.

When NOT to Change a Wheel Yourself

Do NOT attempt to change a wheel if:

  • You’re on a motorway hard shoulder
  • The ground is uneven or sloped
  • Visibility is poor or traffic is heavy
  • You don’t have the locking wheel nut key
  • You don’t feel confident

There’s no shame in calling for help – safety always comes first.

We’re Here If You Need Help

If you’ve fitted a spare wheel and want peace of mind, or if you’d rather not change it yourself:

Pop into Kinson MOT Centre.

We can:

  • Repair punctures (where safe)
  • Replace damaged tyres
  • Check wheel nut torque
  • Supply and fit new tyres
  • Dispose of damaged tyres properly

If you’re in Bournemouth or Kinson and stuck, give us a call – we’ll always try to help or advise you on the safest next step.

Knowing how to change a wheel is a great skill – but knowing when to let a professional take over is just as important.

Share This :