Drivers in Bournemouth and Kinson know how unpredictable British weather can be – one minute it’s sunny, the next it’s pouring. Having clear visibility is crucial, so knowing how to change windscreen wipers on your car is an essential car maintenance skill.
In this friendly guide, we at Kinson MOT Centre will walk you through a step-by-step process to replace your front and rear wiper blades.
Let’s get those wipers changed and get you back on the road with a clear view of sunny Bournemouth!
Why Changing Your Windscreen Wipers Matters
Windscreen wipers might seem like a minor detail, but they have a major impact on your driving safety. Over time, wiper blades wear out – the rubber can crack, split, or harden due to UV sunlight, dirt, and general use. When that happens, you’ll notice streaks or squeaks as the wipers struggle to clear your view. Worn wipers can’t do their job, leaving water or smears on the glass right in your line of sight. This is not only frustrating but also dangerous, especially on rainy Dorset roads.
Importantly, damaged wiper blades can cause your car to fail its MOT test. During an MOT, the inspector will check that your wipers clean the windscreen effectively. In fact, UK MOT guidelines state that any wiper blade that is clearly damaged, worn, or not clearing the screen properly is a fail item. (Washer jets must also work, since empty washers can also lead to a fail.) Many drivers are surprised by this, but it’s true – windscreen wipers not clearing effectively are one of the most common MOT failures. So, keeping your wipers in good condition isn’t just good sense, it’s the law. Don’t let a simple fix like wiper blades be the reason your car doesn’t get that MOT certificate!
The good news is that changing your wiper blades is quick and easy to do at home. Most cars use a simple clip or hook system to attach wipers, so you won’t need any special tools. Below, we’ll guide you through replacing both the front and rear windscreen wipers. All you’ll need are the correct replacement blades for your vehicle, a soft cloth or towel, and a few minutes of time. Let’s get started.
How to Change Front Windscreen Wipers (Step-by-Step)
Changing the front wiper blades (the ones on your windshield) is a straightforward task. Follow these steps to swap out your old, streaky front wipers for new ones:
Get the Right Replacement Blades:
Before anything else, make sure you have the correct wiper blade sizes and types for your car.
Check your owner’s manual or use an online lookup by your car’s make/model or registration number.
Front wiper blades usually come in a pair, and many cars use two different lengths for driver and passenger sides. (For example, a Vauxhall Astra’s front wipers are typically about 22 inches on the driver’s side and 18 inches on the passenger side. Always verify the exact size for your specific model.)
Using the wrong size or connector type can make installation difficult, so double-check that your new blades match your old ones.
Prepare the Car and Windscreen:
Park on a flat surface and turn off your ignition.
Make sure the wipers are in their “parked” position (resting at the bottom of the windscreen).
It’s a good idea to give your windscreen a quick cleaning at this point – remove any dirt or debris so it doesn’t scratch the glass during the process.
Also, have a folded towel or cloth handy and place it on the windscreen beneath the wiper arms.
This will protect the glass in case an arm snaps back down without a blade (preventing a nasty crack).
Lift the Wiper Arms:
Gently pull each wiper arm up, away from the windscreen, until it sticks out and stays in a raised position.
Most front wiper arms will lock in a service position, perpendicular to the glass.
Be careful: the arms are spring-loaded, and without blades they could slam down, which is why we’ve placed a towel underneath.
On some newer cars, you might need to turn the ignition on and off to move the wipers into a vertical position for access – check your manual if you can’t lift the arms freely.
Remove the Old Wiper Blades:
This step can vary slightly depending on the wiper attachment mechanism your car uses.
Most cars use a hook-shaped wiper arm (J-hook).
If yours does, do the following: find the small tab or clip under the wiper where it attaches to the arm.
Press or pull this tab while sliding the old blade downwards (toward the base of the arm) to unhook it.
The blade should slide out of the J-hook and free from the arm.
If your wiper uses a different connector (like a pin or latch), you might need to pop open a cover or push a button instead.
Tip: Pay attention to how the old blade comes off, as you’ll attach the new one the same way. Keep a firm hold on the wiper arm as you remove the blade – remember that spring tension!
Attach the New Wiper Blade:
Take your new wiper and remove any protective covers from the rubber.
Align it with the arm’s hook (or corresponding connector).
For a J-hook, thread the hook through the blade’s center opening and then pull the blade upwards into the hook until you hear or feel it click securely.
If your blade came with adapter pieces, use the one that matches your arm type (these should be indicated in the instructions that come with the blades).
Ensure the blade is firmly locked in place; give it a gentle tug to double-check it’s secure but do not force it.
Lower the Wiper Arm:
Carefully lower the wiper arm back down against the windscreen.
Do this gently – don’t just let it snap down, as that can crack the glass (the towel is there as a safeguard, but it’s best to be safe).
Once the new blade is on, ease it onto the windshield. Now remove the towel from the windshield.
Test the New Wipers:
After you’ve replaced both front wiper blades, turn on your car’s wipers (and washer fluid) to test them.
They should sweep smoothly, with no squeaking, skipping, or smearing. Make sure they are contacting the glass correctly and clearing the water in one pass.
If anything looks or sounds off (e.g. uneven contact or juddering), double-check that the blades are the correct size and properly clipped in.
Otherwise, congratulations – you’ve successfully changed your front windscreen wipers!
How to Change a Rear Windscreen Wiper
Many cars, especially hatchbacks and SUVs, have a rear windscreen wiper. The rear wiper blade is usually shorter than the front ones, and often it attaches differently. Replacing it is also easy; just slightly different in technique. Here’s how to change your rear wiper blade:
Get the Right Rear Blade:
Rear wiper blades come in various styles and sizes.
Make sure to buy one that’s specific to your vehicle’s rear wiper. (For instance, a Ford Focus hatchback’s rear wiper is around 12 inches and uses a particular clip fitting – different from its front wipers.)
Check your car’s manual or parts guide for the correct rear blade type. Using an exact fit ensures it will attach properly and clear the window fully.
Lift or Access the Rear Wiper Arm:
Typically, you’ll need to lift the rear wiper arm away from the back window.
Many rear wiper arms only lift a few inches off the glass (they might not stick out as far as the front ones).
In some models, you might also need to flip up a plastic cap at the base of the wiper or the hinge to get more room. Take care not to force it beyond its intended angle.
Remove the Old Rear Wiper Blade:
Look at how the rear blade is attached – it’s often a different mechanism than the front.
A common rear wiper design is the pin-and-lock (or “Rock Lock”) attachment.
To remove this type: pivot the wiper blade so that it’s perpendicular (at a 90° angle) to the wiper arm.
You may see a small locking clip or tab where the blade meets the arm; press that if present.
Then pull the blade outward, away from the arm, to pop it off the pin.
You might need to wiggle gently – the blade should snap off with a little pressure once aligned correctly. (On some cars like the Ford Focus, the rear wiper blade will pop off after you tilt it and give a firm tug. Don’t try to slide it down a hook as you would with front wipers – rear wipers usually don’t use J-hooks.)
Attach the New Rear Blade:
Take your new rear wiper blade and line it up with the arm.
For a pin-type connector, push the blade onto the arm’s pin until it clicks in place.
Often this means inserting the little pin on the arm into the hole on the blade’s mounting clip, then folding the blade back down parallel to the arm so the lock engages.
If your rear wiper uses a hook or other style, the process will be analogous to the front wiper steps – hook it in or snap it in accordingly.
Ensure it’s firmly attached; you should not be able to pull it off easily once locked.
Gently Lower the Arm:
Once the new blade is securely on, lower the rear wiper arm back against the window.
Make sure it rests properly on the glass.
Double-check that you haven’t left any packaging on the new blade (some have a blade cover you should remove).
Test the Rear Wiper:
Turn on the rear wiper from inside your car to test the new blade.
It should sweep cleanly, clearing away washer fluid or water without streaks.
This confirms the new blade is installed correctly and making good contact with the glass.
If it’s not wiping a certain spot or chattering, re-check the attachment and ensure you bought the correct blade type.
Note: Rear wipers vary quite a bit between car models. Some rear windows (like on certain SUVs or estate cars) are larger and use longer blades; others are small. The attachment method can also differ (pin mount, bayonet, side clip, etc.). If in doubt, consult your vehicle handbook or ask a professional for the exact method for your model. But generally, the above method covers most rear wiper designs.
Pro Tips and Vehicle-Specific Notes
Frequency of Replacement:
For most drivers, replacing wiper blades once a year is a good rule of thumb – typically at the end of winter or before the rainy season. If you notice any of the warning signs (streaking, squeaking, cracked rubber) sooner, don’t wait. Wipers are inexpensive, and fresh ones make a big difference in visibility. Regularly cleaning your windscreen and wiper blades with glass cleaner can also extend their life by removing grit that causes wear.
Vehicle-Specific Sizes:
Always check the required wiper sizes for your specific car. As mentioned, different models have different wiper lengths.
For example, we noted that a Vauxhall Astra from the mid-2000s uses a 22″ driver’s side and 18″ passenger side blade. Meanwhile, a newer Ford Focus (Mk3) might use two 28″ blades on the front, whereas the latest Focus (Mk4) uses a 26″ and a 20″ combination. Using the correct size ensures maximum coverage and proper fit.
Attachment Types:
The common J-hook is found on many vehicles for front wipers, but not all. Some manufacturers use pin arms, bayonet fittings, or side-locking adapters, especially on newer or speciality models. Ford, for instance, has used a side-pin arm on some Focus generations, and Volkswagen/Audi often use push-button releases. Rear wipers often use a small pin lock, as we described for the Focus example. When buying blades, check the packaging – it often lists the compatible arm types or comes with multiple adapter clips to fit various arms. Don’t be intimidated; if the clip on your new blade looks different, it may need a quick swap of the adapter (usually included in the blade kit) to match your arm.
Quality Matters:
Consider investing in good quality wiper blades (brands like Bosch, Valeo, etc.) as they tend to last longer and perform better in heavy rain. Cheap no-brand wipers might save a few pounds but often wear out faster or streak sooner. For our Bournemouth weather – with salty sea air, rain, and the occasional frost – durability is key.
Don’t Forget the Washers:
Your washer fluid system goes hand-in-hand with the wipers. Keep your washer bottle topped up with a good screenwash. If your washers aren’t spraying properly, clean the nozzle tips with a pin. Remember, washers must provide enough fluid for the wipers to clear the screen during an MOT, so make sure they’re working, especially before the test day.
Wipers and the MOT Test: Don’t Risk a Fail
We mentioned it earlier, but it bears repeating: wiper blades can make or break your MOT result. The MOT includes a “Visibility” check, where the inspector looks at your windscreen, wipers, and washers. The official guidance is that any wiper that is not in good condition (torn, ineffective, or missing) can cause a failure.
In plain terms, if your wipers don’t clear the windscreen properly, the tester will “reject” (fail) them. It’s an avoidable problem – a set of new wiper blades costs far less than a re-test fee or fine for driving with a failed MOT.
According to DVSA data, nearly half of MOT failures could be avoided by simple maintenance like replacing worn wipers, bulbs, or tyres. Wipers are actually among the top 3 reasons cars fail MOTs.
So if you’re heading for an MOT in Bournemouth, give your wipers a quick look beforehand. Are they leaving lines or patches of water? Any splits in the rubber? If yes, swap them out before the test. It could save you from a needless failure.
(Fun fact: The MOT inspector will also check that your front washer jets have fluid and can wash the windscreen. An empty washer reservoir or broken washer pump is also a reason to fail. So keep it topped up!)
Need Help? Visit Kinson MOT Centre in Bournemouth
Changing windscreen wipers is one of those DIY-friendly tasks – but not everyone has the time or confidence to do it, and that’s okay!
If you’d rather have an expert take a look, or if you have any trouble fitting your new blades, Kinson MOT Centre is here to help. We’re a friendly local car maintenance and MOT garage in Bournemouth, and our technicians can quickly check and change your wiper blades while you wait.
In fact, when you come in for any service or MOT at Kinson MOT Centre, we’ll inspect your wipers as part of our routine checks. We can let you know if they’re due for a change.
Remember, well-functioning wipers are not just for rainy days – they’re vital for safe driving year-round. Don’t let something as simple as a bad wiper blade compromise your safety or your MOT results.
Call to action: Feel free to visit our Kinson MOT Centre or give us a ring for any help with your wipers. Whether you need new blades fitted, your washer system checked, or just general car maintenance advice, our team is ready to assist. Drop by our Bournemouth garage or contact Kinson MOT Centre today – we’ll make sure your windscreen is clear and your journey is safe, whatever the weather! 🌦️👍